Notification: Our email services are now fully restored after a brief, temporary outage caused by a denial-of-service (DoS) attack. If you sent an email on Dec 6 and haven't received a response, please resend your email.
CFP last date
20 December 2024
Reseach Article

Design and Implementation of Can Bus for Distributed Injection Molding Machine based on Arm Controller

Published on December 2013 by Muthamizhselvi. M, Abraham. M
International Conference on Innovations In Intelligent Instrumentation, Optimization and Electrical Sciences
Foundation of Computer Science USA
ICIIIOES - Number 6
December 2013
Authors: Muthamizhselvi. M, Abraham. M
f4ebe81a-2c14-4456-ac9e-4df2c3ee4aac

Muthamizhselvi. M, Abraham. M . Design and Implementation of Can Bus for Distributed Injection Molding Machine based on Arm Controller. International Conference on Innovations In Intelligent Instrumentation, Optimization and Electrical Sciences. ICIIIOES, 6 (December 2013), 17-20.

@article{
author = { Muthamizhselvi. M, Abraham. M },
title = { Design and Implementation of Can Bus for Distributed Injection Molding Machine based on Arm Controller },
journal = { International Conference on Innovations In Intelligent Instrumentation, Optimization and Electrical Sciences },
issue_date = { December 2013 },
volume = { ICIIIOES },
number = { 6 },
month = { December },
year = { 2013 },
issn = 0975-8887,
pages = { 17-20 },
numpages = 4,
url = { /proceedings/iciiioes/number6/14320-1543/ },
publisher = {Foundation of Computer Science (FCS), NY, USA},
address = {New York, USA}
}
%0 Proceeding Article
%1 International Conference on Innovations In Intelligent Instrumentation, Optimization and Electrical Sciences
%A Muthamizhselvi. M
%A Abraham. M
%T Design and Implementation of Can Bus for Distributed Injection Molding Machine based on Arm Controller
%J International Conference on Innovations In Intelligent Instrumentation, Optimization and Electrical Sciences
%@ 0975-8887
%V ICIIIOES
%N 6
%P 17-20
%D 2013
%I International Journal of Computer Applications
Abstract

In this paper, the distributed intelligent control of plastic injection molding machine based on ARM controller through CAN field bus technology is proposed. The basic components of hardware and Software design are also discussed. The intelligent control system enables the procedure self-learning, fault diagnosing and process parameters such as temperature, injection pressure, flow, limit position etc. , in the molding process. The ARM controller as a slave computer for this control system not only provides on-site monitoring but also can provide distributed remote control services for the host computer. The closed-loop control system, composed of the ARM controller and sensors, realizes the prompt adjustment of the processing parameters in the plastic injection molding machine

References
  1. Distributed Intelligent Control System of the Injection Molding Machine Based on ARM Controller by Zhilei Cui in IEEE Transaction 2011.
  2. Chen Jing; Jiang Xuejun Tan Siyun; Zou Weijun; "Design on controller of plastic injection-molding machine based on multi-CPU ". Environmental Science and Information Application Technology 2010 International conference.
  3. Kedian Wang ; Kai Zhao ; Xia Dong ; . "Design and implementation of an automatic weighing system based on CAN bus . " Advanced Intelligent Mechatronics in IEEE/ASME International Conference 2008.
  4. Ahmed S. F, A new approach in Industrial automation application "Embedded system design for Injection Molding Machine. Multitopic Conference, 2007 IEEE International.
  5. Babur Ozcelik, Alper Ozbay, Erhan Demirbas _ "Influence of injection parameters and mold materials on mechanical properties of ABS in plastic injection molding,"International Communications in Heat and Mass Transfer, Vol. 37, November 2010, pp. 1359-1365.
  6. C. K. Mok, K. S. Chin, Hongbo Lan_"An Internet-based intelligent design system for injection moulds,"Robotics and Computer- Integrated Manufacturing, Volume 24, Issue 1, February 2008, Pages 1-15.
  7. Zhilei Cui, "Computer Safety for Behavioral Protection Mode Based on Artificial Immunity,"Journal of Lanzhou University of Technology, Volume 35, No. 4, Aug. 2009, Pages 107-110.
  8. Chong Jin, Shangping Dai, Jinlei Guo and Wei Zhang, "Artificial intelligence course,"Tsinghua University Press, Jan. 2007.
  9. Zhilei Cui, "Design and Realization of PC-Based Integrated Monitoring System for Multi-Injection Molding Machines," Microcomputer Development, Volume 12, No. 1, Jan. 2002, pp. 85-87.
  10. Hanru Zhong, Qijie Zhou and Muliang Zhong, "Application of intellectual integration in injection machine control,"Journal of South China University of Technology ( Natural Science),Volume 25, Issue 9, Sep. 1997, pp. 6-9.
  11. Pub Z. H. Che _ "PSO-based back-propagation artificial neural network for product and mold cost estimation of plastic injection molding,"Computers & Industrial Engineering, Volume 58, Issue 4 May 2010, pp. 625-637.
Index Terms

Computer Science
Information Sciences

Keywords

Arm Controller Can Bus Injection Molding Machine Distributed Control System Artificial Intelligent Control.